BETAFPV F405 2-4S AIO Brushless Flight Controller 12A&20A (BLHeli_S) V3 for Beta75X Beta85X HX100 FPV Toothpick Racing Drone

F405 2-4S AIO 12A Brushless Flight Controller (BLHeli_S) V3 has been updated the F411 chip to F405, which can totally handle 12A continuous current(13A burst), gives pilots a powerful flight. Highly recommended using it on Beta75X series drone, Beta85X series drone and HX100 series drone such as Beta85X V2 and Beta85X HD Digital VTX.
The 20A F405 AIO Flight Controller decreases the board thickness from 1.6mm to 1.2mm, which reduced the weight to 5.3g while improving the ability of the ESC to continuous current 20A(22A burst). Now you can build a bigger quad with powerful Flight Controller to save weight and size such as the Beta95X Digital VTX, Beta95X V2 and Beta95X V2 HD Digital VTX.

Because 12A V3 Flight Controller and 20A AIO V3 Flight Controller have unified the UART, both two boards have the same appearance, Flight Controller diagram, statue LED and way to connect the RX. 

Bullet Point

• Updated the F411 chip to F405, this new 12A/20A board can handle 12A/20A continuous current(13A/22A burst), gives the pilots a powerful flight. 
• Come with 2 integrated Plug & Play Ports for both digital VTX and Rx, less solder work needed, easy to install. 
• Completed the traditional mounting hole, more like the Toothpick type, perfectly prevent the damping pad from falling off, which is the super-easy installation in most whoop frame.
• BETAFPV 20A/12A AIO flight controller will unify the UART, which is convenient for pilots to solder.
• Compatible with 110X, 120X, 140X motors, pilots can use the 20A(12A) AIO Flight Controller to build a bigger quad with this powerful Flight Controller to save weight and size.

Comparison of F4 12A AIO Flight Controller V2, F405 12A AIO Flight Controller V3 & F405 20A AIO Flight Controller V3

Specifications of F405 20A AIO Flight Controller V3

• CPU: STM32F405RGT6
• Six-Axis: MPU6000
• Size: 26mm x 26mm
• Firmware version: Batefight-BETAFPV405-4.2.X
• OSD: Built in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
• Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver/DSMX Receiver
• Connecter: XT30 (Suitable for XT30/XT60)
• Weight: 5.3g

Specifications of ESC

• Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300，Dshot600
• Input voltage: 2S-4S Lipo
• Continuous current: 20A
• Peak current: 22A
• Firmware: BLHELI-S G-H-25

Specifications of F405 12A AIO Flight Controller V3

• CPU: STM32F405RGT6
• Six-Axis: MPU6000
• Size: 26mm x 26mm
• Firmware version: Batefight-BETAFPV405-4.2.X
• OSD: Built in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
• Receiver: Support Frsky XM/XM+FCC Receiver/ Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver/DSMX Receiver
• Weight: 5.3g
• Connecter: XT30

Specifications of ESC

• Support PWM，Oneshot125，Oneshot42， Multishot，Dshot150，Dshot300，Dshot600
• Input voltage: 2S-4S Lipo
• Continuous current: 12A
• Peak current: 13A
• Firmware: BLHELI-S G-H-25

Diagram for F405 20A AIO Flight Controller V3 & F405 12A AIO Flight Controller V3

Package

• 1 * F405 20A AIO Flight Controller V3 or F405 12A AIO Flight Controller V3
• 4 * M1.2x4mm screws
• 4 * M1.4x5mm screws
• 4 * Anti-vibration rubber dampers
• 1 * 6-Pin Connector for Digital VTX
• 1 * 4-Pin Connector for Rx