Home>DIY RC Drone Accessories>DIY Mobula6 Mobula7 1S Flight Controller CineWhoop RC Quadcopter With Camera Flysky T-pro Transmitter FPV Goggles

DIY Mobula6 Mobula7 1S Flight Controller CineWhoop RC Quadcopter With Camera Flysky T-pro Transmitter FPV Goggles Item NO.: F24736-A----F24736-H

Name: DIY Mobula6 Mobula7 1S Flight Controller CineWhoop RC Quadcopter With Camera Flysky T-pro Transmitter FPV Goggles
SKU: F24736-A----F24736-H
Price: 164.25 USD
Availability: InStock

Write a Review

US$ 164.25

US$ 193.24 Save US$ 28.99 (15% Off)

Color

Quantity: Stock ( 79999992 )

Estimate Shipping Cost

Add to Cart

Product Name	DIY Mobula6 Mobula7 1S Flight Controller CineWhoop RC Quadcopter With Camera Flysky T-pro Transmitter FPV Goggles
Item NO.	F24736-A----F24736-H
Weight	2 kg = 4.4092 lb = 70.5479 oz
Category	DIY RC Drone Accessories
Creation Time	2022-03-30

mobula7 configuration:

Spare Parts Specifications:
motor
Model: 0802 KV20000
Configuration: 9N12P
Stator diameter: 8 mm
Stator length: 2 mm
Shaft diameter: Φ1 .5 mm
Motor size (Dia.*Len): Φ 10.5 mm*1 3.5 mm
Weight (g): 2.0 g
Voltage: only 1S

propeller
Weight: 0.24g
Material: PC
Spacing: 1 inch
Diameter: 40mm
Center thickness: 5mm
Center hole diameter: 1.5mm

flight control
X12 ELRS V1.0 flight control built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280
X12 Frsky V1.0 flight control built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR
X12 Flysky V1.0 flight control built-in SPI Flysky 2.4G receiver Target: CRAZYBEEF4FS

MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU6000 or ICM20689 (SPI connection)
Mounting hole size: 25.5mm*25.5mm
Power supply: 1 S battery input (DC 2.9V - 4.35 V) built-in 12 A (each) Blheli_S 4-in-1 ESC
Built-in Betaflight OSD (SPI Control) Built-in 5.8G OpenVTX 0mw~400mw Built-in ExpressLRS 2.4G, Frsky D8/D16, Flysky AFHDS 2A Built-in voltage detection
Built-in current sensor

Onboard 4-in-1 ESC
Power supply: 1 S LiPo/LiPo HV
Current: 12 A continuous peak 15 A (3 seconds) supports BLHeliSuite
Programmable factory firmware: Z_H_30_REV16_7.HEX
Default protocol: DSHOT 3 00

Onboard SPI ExpressLRS 2.4GHz receiver
Packet rate options: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware Version: V2.0 RF Frequency: 2.4GHz
Antenna: Patch Antenna Telemetry Output Power: <12dBm
Receiver Protocol: SPI ExpressLRS
Compatible with ExpressLRS V2.0 TX modules
Cannot flash ExpressLRS firmware alone

Onboard Frsky SPI D8/D16 receiver version
SPI BUS Receiver Frsky D8 Compatible Compatible with Non-EU Transmitter D8 Models
Channel: 8ch without ground interference (transmitter and receiver are 1 meter away from the ground): 200 meters
Failsafe support

Onboard Fly sky SPI receiver version
SPI BUS receiver protocols: AFHDS and AFHDS-2A
Switchable channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference (transmitter and receiver 1 m from the ground): 200 m failsafe support

image transmission
Smart Speaker v2.1
Pit mode support
RCE mode support
Channel: 48ch
Transmit power: 0/RCE/ 25mw/100mw/ 4 00mw
Power supply: DC 5V
Current (5v): <650ma (4 00mw)

camera
Model: RunCam Nano 3
Image Sensor: 1/3" CMOS
Horizontal resolution: 800TVL
Lens: 2.1mm(M8) FOV 1 5 0°
Signal system: NTSC
Signal-to-noise ratio: >50dB
Electronic Shutter Speed: Auto
Automatic Gain Control (AGC) : Automatic
minute. Illumination: 0.01Lux@1.2F
D-WDR : Automatic
Day/Night: Color
Power supply: DC 3-5.5V
Current: 110mA@5V 120mA@3.3V
Shell material: ABS
Net weight: 1.2g
Size: L14mm*W14mm*H9mm
lithium battery
Capacity: 65 0mAh
Voltage: 3.8v
Continuous discharge rate: 30C
Instantaneous discharge rate: 60C
Dimensions: 60mmx18mmx8mm
Weight: 16g
Connector: PH2.0

mobula6 configuration:
AIO flight control with ELRS receiver and 5.8G VTX
Ultralight 1S 65mm brushless whoop only 18.7g
Device with lightest brushless motor - SE0702 only 1.46 grams
Runcam Nano3 Lightest 1/3 CMOS 800TVL Camera
smooth and powerful
Compatible with 1S Lipo/LIHV
Specification:
Product name: Mobula6 ELRS version
Wheelbase: 65 mm
Size: 80mm*80mm*37mm
Weight: 18.7g

Note: Please refer to our pictures to choose the desired combination, all parts are sold separately in our store, you can add as spares. If you have any questions, please feel free to contact us.